产品中心
PTFE脱模剂/润滑喷剂
1.产品名称:PTFE(特氟龙)润滑喷剂
2.产品编号:CS-206
3.产品品牌:“CSHPON”品牌
4.生产单位:在邦OEM基地
5.耐温区间:-150--250℃
6.产品规格:500ML
7.产品特性: 快干、润滑、耐磨、清洁 
8.产品包装:500ML/罐;24罐/件
9.中性包装:可根据客户使用要求加工
10.联系电话:021-20955711
网上店铺在线订购
  • 产品说明书
  • 产品MSDS
  • 执行标准
  • 文献资料

PTFE(特氟龙)脱模剂/润滑喷剂是由超细聚四氟乙烯粉末、高粘溶胶、分散剂、乳化剂和推进剂,通过高压气雾混合灌装生产。有良好的成膜性、附着力强、润滑性和耐磨性,同时具有耐腐蚀性、抗极压性和耐高温。广泛应用于机械、造船、钢铁、纺织、锻造、五金和航空等行业。

 

产品特点

1. 适合白色润滑概念的要求场合,具有良好的抗极压,防锈和润滑性能,附着力强。

2.耐温区间:耐温区间: -190℃—327℃,最佳工作耐温区间: -150℃~250℃。

3.机械性能:具有良好的机械韧性;即使温度下降到-196℃,也可保持5%的伸长率。

4.耐腐蚀性:对大多数化学药品和溶剂,表现出惰性、能耐强酸强碱、水和各种有机溶剂。

5.高润滑性:罐液吸附在工件表面,形成一个保护膜与膜紧密,摩擦系数小,起到很好的保护润滑。

6.技术成熟,质量稳定,便于携带,使用方便。

使用方法

1.使用前,用力摇晃喷罐约80秒,以使罐液均匀,利于喷涂。

2.请将需要润滑部位的油污和灰尘清洗干净。

3.保持喷口距离工件约30cm,来回移动,不要固定在一个位置,表干约30秒钟。

4.使用后长时间不用时,必须倒转罐身喷出几下,清洗喷嘴,以防止喷嘴堵塞。

5.详细阅读产品使用说明书,并在专业人士指导使用。

注意事项

1.本品不含氟利昂。严禁烟火,注意室内通风。

2.存储在40℃环境下,直立罐体,空罐勿抛入火中。

3.不要使罐内液体接触眼睛,如果不小心溅入眼睛,请立即用流动清水或生理盐水冲洗。

4.如果罐液不慎入口,应及时到医院急诊并采取相应的处理措施。

5.禁止放置于在儿童可触及的地方,以免发生意外。

6.严禁在阳光下曝晒或存放在车里暴晒。

7.禁止敲击投掷罐体,运输过程中应小心轻放。

包装贮存
1.包装:500ml/罐,12罐/件,24罐/件。
2.贮存:贮存于阴凉、干燥通风处。

------------------------------------------------------------------------------------------------------------

PTFE (Teflon) / grease spray release agent(CS-206)

Release agent for PTFE (Teflon) / spray lubricant is by superfine PTFE powder, high viscosity sol, dispersing agent, emulsifier and propellant by high-pressure aerosol mixing and filling production. Has good film forming, adhesion, lubrication and wear resistance, at the same time, it has the ability of anti - corrosion, anti - extreme pressure and high temperature. Widely used in machinery, shipbuilding, steel, textile, forging, metal and aviation industry.

Product features

1.Suitable for the concept of white lubrication occasions, has a good anti - pressure, anti - rust and lubricating performance, strong adhesion.

2.Temperature resistance range: -190 temperature range: 327, the best working temperature range: -150.

3.Mechanical properties: with good mechanical toughness; even if the temperature drops to -196, but also can maintain the elongation of 5%.

4. Corrosion resistance: for most chemicals and solvents, inert, showed the ability of acid alkali, water and organic solvent.

5.High lubricity: Tank adsorbed on the surface of the workpiece, formation of compact film and a protective film, small friction coefficient to good lubrication protection.

6.Mature technology, stable quality, easy to carry, easy to use.

Using method

1.before use, shake the spray tank for about 80 seconds, in order to make the tank liquid even, which is beneficial to the spray.

2.Please clean the oil and dust in the lubrication region.

3.To keep the nozzle distance of about 30cm, to move back and forth, not fixed in a position, the surface is dry for about 30s.

4.Use a long time without the need to reverse the tank body, a few times to clean the nozzle, to prevent the nozzle plug.

5.Read in detail the use of the product manual, and the use of professional guidance.

Note

1.This product does not contain freon. No fireworks, pay attention to indoor ventilation.

2.Stored in the environment of 40 degrees, the vertical tank, empty tank not thrown into the fire.

3.Do not allow the liquid to contact the eyes, if accidentally splashed into the eyes, please rinse immediately with the flow of water or saline.

4.If the tank liquid accidentally entrance, should be promptly to the hospital emergency and take the corresponding treatment measures.

5.Prohibition of the place where children can reach, to avoid accidents.

6.Non exposure or stored in the car in the sun exposure.

7. No knocking throwing tank, be careful in the process of transportation.

Packaging and storage

1.Packing: 500ml/ can, 12 cans / pieces, 24 cans / pieces.

2.Storage: stored in a cool, dry and ventilated place.


点击下载